For more information visit us at www.HydrogenKo.com ++++++++++++++++++++++++++++++++++++++++++++ 13 plate dry cell equipped with a 30 amp relay and 30 amp circuit breaker. produces 1.3 LPM at 20 amps. great little cell for use in a car or truck. small 6x8x2
Environmentally Friendly Stop
Friendly Poll
Loading ...
{ 25 comments… read them below or add one }
buy a piece of pvc from mcmaster carr
I am still having issues finding the two end plates, at home depot and lowe’s they just got little 1/4″ acrylic and nothing thicket. Tried using a cuttingboard but its not flat so i get leaks…..
This produces both hydrogen and oxygen, hence HHO!
so this thing makes hydrogen and then you could use the hydrogen for car fuel?
Did you see my video on producing more hho by find the sweet spot ,by slowing the flow.
Thats a nice way to mike firecracker sounds on the 4th. And its legal!
Very Nice… Love your designs! I have truley been inspired the last hour by your designs.~ THANK YOU!
not in may case; i tried it and it blew in my van from heat. good luck to you! i’m using a pump now.
give this setup a try. as the HHO is forced up the tube it creates a back preasure on the intake tube making a pumping action. the water is circulated through the system.
air is lighter than water: only bubbles will travel upwards. water can not fight the gravity, unless a pump is used or by capillarity action. as a result, your electrolizer will get hot soon.
Can a video be made of the layout of the cell?
a good rule of thumb is not to use over 20-25% of your alternator’s max output
Oh 120amp, thats great.
The european things we drive, have only 55 – 95amps(thats the max. i found, for my budget.)
With 30amps, oh that would be great to use *dreaming*.
Is there a formula, to calculate the free amps, that are aviable in a car?
Must i look at all used carparts(windowlifter, etc..) and then in the manual, with what the line is fused?
Forgive me my bad english (where is the redfaced smiley).
it just depends on the cars alternators output. my dodge neon has a 120amp rating. so im ok to put 25-30 amps from it.
How many amperes can a car give away, so that the battery is charged too?
)
Our european Cars never can support 20 Amps, but thats only what i think.
If i light bubbles of that size, my boom is bigger
I have the same plastic reservoir and it has a vented cap. You need to plug the hole in the cap and conduct a new test. I can tell from experience that you are producing closer to 4.0lpm than 1.3lpm
Very nice.
Look up a roofing supply house , or find a construction company that does rubber if you ask they may have scraps , we throw away small pieces like under a few feet. You can get epdm in diffent thickness up to pretty dam thick.
yes this is my own. i had the plates cut to my specs. i don’t have a veriac so i wont be able to put more than 11.5v into it until i get it into the neon. i received 208 plates today to build some of these and i also have 112 9×9 plates that i plan building one massive dry cell with. stay tunned for that video in a couple of weeks.
Wow Delvis, >5MMW. It’s no secret that a well-built dry cell is efficient. Could you show it at 14V? I’m curious to see the efficiency as it would be run in a vehicle.
Did you build this one all from scratch? I know that a vendor in the UK was selling nice U-assemble kits for around $250.
Were can I get this. I looked it up on the internet and they want to sell it in sheets. Did you make you own or have them cut by someone. Also is the outside layer plexiglass 1/2 inch. Hey thanks for the responce.
Where do you buy your fluid reservoir from?
i made the gaskets out of EPDM rubber. the unit has been running for over 100 hours with no sign of leaching from either the plates or the rubber.
What did you use to seal the plates so it wouldn’t leak. I know it was probably a gasket but did you make it or did you use something off the shelf. Great video.
im using KOH. one thing i didn’t mention in the vid is that i have literally had it running for a week straight with no heating problems and the water is still perfectly clear of any scum.
You must log in to post a comment.